ruseng
"Stromizmeritel" LLCHigh technologies in sphere of manufacture of glassmixture and differrent multicomponent mixtures
(930)70-679-70
Automation of technological processes
Automation of technological processes
Installation and start-up of equipment
Installation and start-up of equipment
Installation and start-up of equipment
Batch equipment
Batch equipment
Batch house design
Batch house design
Service maintenance
Service maintenance
Service maintenance
Тechnology of multicomponent mixtures preparation
Тechnology of multicomponent mixtures preparation

Two-roll crusher

APPLICATION OF THE TWO-ROLL CRUSHER
Two-roll crushers DV2-10А and DV2-15А are designed for crushing of waste in production of glassware with wall thickness of max. 12mm. Two-roll crushers DVS2-10А and DVS2-15А with stepped drums are designed for crushing of waste in production of sheet glass with sheet thickness of max. 12mm.
Operation conditions of the crusher:
-    ambient temperature, °С (К)…………from -30 to +40 (243-313)
-    relative air humidity, %……………90 (at t=25°С)
-    atmosphere pressure, kPa (mm Hg),…………84-106,7 (630-800)
-    parameters of electric power supply are indicated in the table.

MAIN TECHNICAL DATA

The main technical data is indicated in the table
Parameter
DV(S)2-10А
DV(S)2-15А
Capacity, tons/hour
6…10*
9…15*
Grain size after crushing, mm
5….30
5….30
Rotation frequency of the driven shaft, rotations/min.
60
60
Adjustable clearance between roll drums,mm
5…40
5…40
Gear motor type
A503 NH55 24,0 S4 B3 M4SA4
A503 NH55 24,0 S4 B3 M4LA4
Nominal power of the drive, kW
11 (2x5,5)
15 (2x7,5)
Number of gear motors
2
2
Electric power supply voltage, V
380±38
380±38
IP code of the electric motor
IP55
IP55
Overall dimensions (l:w:h), mm
1110:1790:745
1510:1790:745
Weight, max., kg
925
1190
* – actual capacity depends on the properties of the processed material and crushing conditions.

DESING AND OPERATION PRINCIPLE

устройство дробилки двухвалковой

Two-roll crusher DV2 consists of the following units (see picture 1): a body, two roll drums pos.1, bearing assemblies pos.17, swivel levers pos.6, a loading unit with lining plates pos.2, a loading flange pos.5, two inspection covers pos.13, two gear motors pos.16, installed on the shafts of the roll drums pos.9.

The crusher body consists of two front pos.7 and two side walls pos.8, connected to each other by means of bolt joints. Inside the body lining plates are fixed to the walls by means of bolt joints. Four brackets pos.3 fixed on the front walls, around the axles of which the swivel levers pos.6 with bearing assemblies fixed on them pos.17 are swinging. The bracket and the swivel lever are connected to each other by a bolt pos. 11.
Adjustment of the operation clearance between the roll drums pos.1 is done by changing of the inclination angle of the swivel levers pos.6 around the bracket axles pos.3 by means of screw drawing pos.10.

To eliminate the crushed material getting into the bearings of the bearing assemblies pos.17 a safety washer pos.15 and a ring pos.12 are installed on the shaft of the roll drum pos.9 between the front wall pos.7 and the bearing assembly. Material for crushing is supplied through the loading flange pos.5 fixed on the crusher body and gets between rotating towards each other roll drums pos.1. During rotation of the roll drums the crushed material is drawn between the drums and is crushed. Further the crushed material is unloaded through the output gate of the crusher.

Springs pos.14 with screw drawing pos.10 serve as a safety element when bodies which cannot be crushed get into the crusher, they prevent damage of the critical units and parts. Strength of the material crushing is adjusted by the spring load level.

 

Gallery

 
 
© 2018 "Stromizmeritel" company
Site map
System
quality
management
34 A Sovnarkomovskaya Street, Nizhny Novgorod, Russia, 603086
+7 (831) 435-13-70